CarWell CP90
Rust Inhibitor, Lubricant, Penetrant
Stop and inhibit rust, aluminum oxide, “greening” on wiring, and corrosion from dissimilar metals! CarWell Rust Inhibitor CP-90, aka T-32, is a unique blend of rust inhibitors to control corrosion on ALL metals. It eliminates moisture containing salt, dirt, and air pollutants from the surface of metal to give long lasting protection. It also lubricates moving parts and is an excellent penetrant, even through existing rust. CP-90 does not harm painted surfaces (including CARC paint), plastics, rubber, glass, or wiring.
Application of CP-90 will control corrosion and extend the use of your vehicle and equipment when applied on a regular maintenance program. It can be used on new, used, and even rusted areas or equipment parts (recommended: Evapo-Rust for rust removal). CP-90 can be applied to more areas than any other conventional rust protection like batteries, working mechanisms and moving parts (see list for typical application areas). CP90 is easy to apply, easy to clean-up and the vehicle or equipment can be returned to service immediately. Note: for aircraft/aerospace parts, large and/or flat surfaces (non-creep areas), we highly recommend AR500 Corrosion Inhibitor.
The CarWell product and product support have been used successfully for over ten years and currently are used by many military and commercial fleets including U.S. Army, U.S. Postal Service, FedEx, and UPS. CarWell has Department of Transportation Approval and is safe to use.
CP-90 reduces downtime, controls and prevents corrosion and provides lubrication on all moving parts.
OUTSTANDING BENEFITS AND FEATURES:
No VOC’s- No CFC’s
- Non-Flammable
- 100% Non-Conductive
- No Teflon
- No Solvents
- No Silicone
Directions:
Apply CarWell CP-90to a vehicle/part and allow to cure for a minimum period of 48 hours. After 48 hours CP-90 has fully penetrated the metal and can be left on or washed off with a mild environmentally friendly cleaner/degreaser such as VPW SC-1000, SC-Aircraft & Metal Cleaner, or All Clean.
Surface Repainting
To repaint an exterior surface after CP-90 has been applied, clean the surface with a preparation solvent as usual. Prime within 1 to 2 hours before CarWell is allowed to creep and return, then top-coat as per paint manufacturer’s directions and then re-apply the CarWell product in appropriate areas.
| ASTM B117 - saltfog (modified) 500 hours | ASTM D4541 - Pull-off Adhesion - HATE |
|---|---|
| GM 9540P - cyclic corrosion test (modified) 80 Cycles | ASTM D522 - Mandrel Bend - Adhesion |
| ATC test track - pre exposure to live agent | IR - per CARC specifications |
| Live agent testing (per CARC specs) | Gloss - per CARC specifications |
| ASTM G53 - Fluorescent UV Condensation (QUV) | ASTM D3363 - Pencil test (film hardness) |
| ASTM D3359A - Wet Adhesion | DS2 - Resistance |
| ASTM D3359B - Dry Adhesion |
CARC Vehicle Wash Procedures - Carwell Rust Inhibitor CP-90 is a recommended and approved corrosion CPC product used on vehicles. The Carwell CP-90 product, in addition to its conventional areas of benefits (seams, joints, dissimilar metals, internal cavities, flash rust control), can be used on vehicles and equipment for line of sight applications for ocean transportation, long-term storage or any other situation that is in highly corrosive areas. It is not necessary to apply Carwell to the rubber, fiberglass or Kevlar composites.
DIRECTIONS
After Carwell CP-90 is applied to a vehicle, the vehicle should be allowed to cure for a minimum period of 48 hours and then any excess product should be washed off. For washing and removal of Carwell, consider the following:
- Use an environmentally approved biodegradable mild degreaser such as VPW SC-1000 or SC-Aircraft & Metal Cleaner.
- Use water temperatures between 100 - 200 F.
- Use pressure washer capable of 2000 to 3500 psi.
- Pressure washer tip should be kept 18 inches away from surface.
- For instances where pressure washers cannot be utilized, wipe down throughly.
If uncertain as to the necessity of washing the vehicle, usually wash:
- After shipments arrive at their port of destination.
- After long term storage.
- After return from a maintenance motor pool.
Following this procedure maximizes readiness and reduces O/S costs, while ensuring the CARC service is well within all guidelines as per ARL's reporting.
SURFACE REPAINTING
To repaint an exterior surface after Carwell has been applied, clean the surface with a preparation solvent as usual. Prime within 1 to 2 hours before Carwell is allowed to creep and return, then top-coat as per paint manufacturerÕs directions and then re-apply the Carwell product.
WHEN TO APPLY
- Every six (6) to nine (9) months - in corrosion prone environments such as coastal or heavy industrial areas
- Yearly - in the Rust Belt (Northeast U.S.)
- Every two to three years - West & South
- As required to corroded vehicles
- Immediately after exposure to extreme environmental factors such as salt water wash, acid bath, sandstorm, etc.
- GSA Contract # GS-07F-0341N, CAGE CODE: 1GZV7
|
|
|||
16 Oz. Pump Spray |
CP90-16c | $ 9.95 | |
1 Gallon |
CP90-1c | $ 46.67 | |
5 Gallon |
CP90-5c | $ 197.37 | |
| 55 Gallon | CP90-55c | $ 1384.43 | |
(c) Orison Marketing 2009